>Product>Current Probe>AC Current Clamp>Bus Bar Ac 2000a Clamp On Current Transformer

clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer
clamp on current transformer

Q125BUS BAR AC 2000A CLAMP ON CURRENT TRANSFORMER

The model Q125 2000A current transformer clamp on measuring instrument can be used for a current vector for the copper bar or the power aluminum bus bar on-line detection. It has a 120mm * 50mm square hole, make it specially suitable for bus bar current measurement. In this method, there is no need to break a circuit or to affect the isolation to measure the current. it can be applied for energy meter & power meter, Standard IEC61869 & CE. easy installation, measurement 3000A big current value.

Request a quote Download Catalogue video

APPLICATION

■ HVAC;

■ Power meter;

■ Oscilloscopes;

■ Electrical utility;

■ Plant maintenance;

■ Electrical Laboratory;

■ Large industrial loads;

■ Data logging/recording;

■ Power quality analyzer;

■ Power load monitoring;

■ Industrial maintenance;

■ Power quality monitoring;

■ Power and harmonic meters;

■ Calibration instrument on site;

■ Energy meter calibrator on site;

■ Measuring around cable bundles;

■ Clamp type ground resistance tester；

FEATURES

■ UL, CE CNAS mark;

■ Frequency 40Hz-2000Hz Bandwidth;

■ Conforms to EN 61010, 600V CAT III;

■ Large bus bar jaw opening designed;

■ Measurement range of 1A to 3600A AC;

■ Holding wire diameter: φ120mm×50mm;

■ Low phase shift for power measurement;

■ Industrial design & beautiful appearance;

■ Transformation ratio: 1000:5, 2000:5, 3000:5

■ High precision 0.2% for current measurement;

■ Improved ergonomic design & easy operation;

■ Output:5mA AC/A AC, 2.5mA AC/A AC, 1.666mA AC/A AC

■ Nominal range: 1 to 1000AAC, 1 to 2000AAC, 1 to 3000AAC

■ When less than 1A output, load capacity ≤20Ω; When 5A output, load 2.5VA;

■ Designed for recorders, loggers, oscilloscopes, power and harmonic meters;

PARAMETERS

Electrical parameters
Ratio 1000: 1 or 2000:1 (customized)
Accuracy class 0.2%, 0.5%, 1%
Primary current 0 - 3000A AC
Secondary current 0 - 5A AC (customized)
Max. Cont. Input current 3600A
Over voltage category CAT III 600 V
Output signal (AC current) 500mA,1A,5A AC at nominal input current
Output signal (AC voltage) 333mV,500mV,1V,5V AC at nominal input current
Frequency range 40Hz-2000Hz
Dielectric strength 3KV 50Hz/60Hz at 1 minute
Temperature range -20°C to +55°C
Output 2.5 meter cable with D01 connector
Max. voltage not insulated conductors 720 V
Standard EN 61010-1, EN 61010-2-032, EN 61010-2-031
IEC60044-1, & IEC61869-2, 600V CAT III
Installation Clamp type
Output mode Lead output (2.5m)
Connector BNC, 4mm banana, signal cable(2 cores),customized
Mechanical parameters
Dimensions (L x W x H) (mm) 116 x 327 x 35
Weight (g) 1200
Holding wire diameter (mm) φ120 x 50
Max. jaw opening (mm) 50
Jaw color White or Blue
Material PC+ABS, UL94 V0

SELECTION GUIDE

Model Rate Current Max Current Secondary Coil Ratio Burden Resistance Accuracy
Q125A5-500 500A 600A 5A 100:1 2.5VA 0.5%
Q125A5-600 600A 720A 5A 120:1 2.5VA 0.5%
Q125A5-800 800A 960A 5A 160:1 2.5VA 0.5%
Q125A5-1000 1000A 1200A 5A 200:1 2.5VA 0.5%
Q125A5-2000 2000A 2400A 5A 400:1 2.5VA 0.5%
Q125A5-3000 3000A 3600A 5A 600:1 2.5VA 0.5%
Q125A1-1000 1000A 1200A 1A 1000:1 2.5VA 0.2%
Q125A1-2000 2000A 2400A 1A 2000:1 2.5VA 0.2%
Q125A1-3000 3000A 3600A 1A 3000:1 2.5VA 0.2%
Q125A2-500 500A 600A 250mA 2000:1 customized 0.2%
Q125A2-1000 1000A 1200A 500mA 2000:1 customized 0.2%
Q125A2-2000 2000A 2400A 500mA 4000:1 customized 0.2%
Q125A3-1000 1000A 1200A 400mA 2500:1 customized 0.2%
Q125A3-2000 2000A 2400A 400mA 5000:1 customized 0.2%
Q125A4-1000 1000A 1200A 250mA 4000:1 customized 0.2%
Notes: Can be customized current probe according to user requirements!

RELATED PRODUCTS